Saturday, 2021-01-09

*** tpb has joined #litex00:00
*** lf has joined #litex00:14
*** lf_ has quit IRC00:14
*** kgugala_ has quit IRC00:17
*** chgavilana has quit IRC02:02
*** kbeckmann1 has quit IRC03:11
*** kbeckmann has joined #litex03:12
*** Degi_ has joined #litex04:22
*** Degi has quit IRC04:23
*** Degi_ is now known as Degi04:23
*** [Matt] has quit IRC04:46
*** [Matt] has joined #litex05:15
*** martinraison has joined #litex06:15
*** martinraison has quit IRC06:20
*** _whitelogger has quit IRC06:39
*** _whitelogger has joined #litex06:41
*** peepsalot has quit IRC06:49
*** peepsalot has joined #litex06:57
*** Bertl_oO is now known as Bertl_zZ07:13
_florent_Hi ethanhs, the Trellisboard is not commercially available but a few batches have been made. I know somlo here made at least one batch but don't know if the he has some remaining to sell08:48
_florent_Otherwise, for PCIe / low cost if you want to play with LiteX I would recommend an Artix7 based board for now (LitePCIe currently does not support ECP5)08:49
*** martinraison has joined #litex08:50
_florent_Ethernet is supported on both several FPGA devices (Artix7, ECP5, etc...) but the Acorn does not have Ethernet natively. (but it could be done with the SerDes and a SFP/1GBps Ethernet module).08:51
_florent_If you don't need PCIe, the Arty is also a nice, not to expensive board that is now supported by SymbiFlow08:52
_florent_On ECP5, there is also the new ECPIX-5: https://shop.lambdaconcept.com/home/46-1-ecpix-5.html08:54
tpbTitle: ECPIX-5 (at shop.lambdaconcept.com)08:54
*** martinraison has quit IRC09:12
ethanhsHi _florent_, thank you so much for the info!09:14
ethanhsMy project needs ethernet and pcie unfortunately, so I might need to look at SerDes09:16
*** martinraison has joined #litex09:19
*** keesj has quit IRC09:25
*** keesj has joined #litex09:27
*** keesj has quit IRC09:32
*** keesj has joined #litex09:45
*** keesj has quit IRC09:53
*** keesj has joined #litex10:22
*** martinraison has quit IRC10:25
*** martinraison has joined #litex10:26
*** keesj has quit IRC10:52
*** keesj has joined #litex11:04
*** martinraison has quit IRC11:40
*** martinraison has joined #litex11:49
*** martinraison has quit IRC12:27
*** ethanhs has quit IRC12:42
*** martinraison has joined #litex12:47
*** martinraison has quit IRC12:51
*** Bertl_zZ is now known as Bertl13:21
*** martinraison has joined #litex15:07
*** martinraison has quit IRC16:12
*** martinraison has joined #litex16:16
*** Bertl is now known as Bertl_oO16:18
*** martinraison has quit IRC16:55
*** chgavilana has joined #litex17:03
*** kgugala has joined #litex17:09
*** andrewb1999 has joined #litex18:44
andrewb1999Has anyone used the pynq z1 with litex before?18:46
andrewb1999I don't think it should be much different from the zybo z7, but I'm not sure if the zybo z7 target is intended for the 7010 or the 7020 variant18:47
zyp7010: https://github.com/litex-hub/litex-boards/blob/master/litex_boards/platforms/zybo_z7.py#L9619:01
andrewb1999zyp: I see.  Is there any work to support the 7020 ps?19:02
zypI figure you just change that line to read xc7z020 instead :)19:03
andrewb1999zyp: I'm not sure if the 7020 PS to PL IOs are the same as the 7010 but I will cross my fingers and try it.19:04
daveshahafaik the PS7 is the same across all Zynqs19:05
andrewb1999daveshah: Ok thanks, that would definitely make it easier19:06
*** martinraison has joined #litex19:31
*** martinra_ has joined #litex19:32
*** andrewb1999 has quit IRC19:34
*** martinraison has quit IRC19:36
*** andrewb1999 has joined #litex20:56
*** martinra_ has quit IRC21:00
*** martinraison has joined #litex21:01
*** martinraison has quit IRC21:06

Generated by irclog2html.py 2.17.2 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!