| *** tpb has joined #timvideos | 00:00 | |
| cr1901_modern | mithro: What would cause the following behavior (device number 12 and 13). | 00:00 |
|---|---|---|
| cr1901_modern | The Opsis came back as a JTAG device in between showing up as unconfigured | 00:00 |
| mithro | cr1901_modern: that is normal | 00:02 |
| mithro | cr1901_modern: the FX2 boots faster than the FPGA, so it comes up in unconfirmed mode. The gateware boots and it now it is ready, it resets the FX2 which then loads the real firmware from the FPGA. | 00:03 |
| mithro | cr1901_modern: this also means that if the gateware doesn't boot, the FX2 will just appear in unconfigured mode | 00:04 |
| mithro | Makes sense? | 00:04 |
| cr1901_modern | mithro: Okay, that makes sense then. | 00:04 |
| cr1901_modern | I must've actually done the power cycle between 13 and 14 then (I don't remember lol) | 00:04 |
| cr1901_modern | mithro: I had to do a power cycle to get rid of the proxy bitstream when flashing the EEPROM | 00:05 |
| mithro | Flashing the EEPROM? | 00:06 |
| cr1901_modern | mithro: Err sorry | 00:06 |
| cr1901_modern | I meant flashing the SPI Flash | 00:06 |
| * cr1901_modern has _NOT_ touched the eeprom tonight | 00:06 | |
| mithro | Okay. Bblr | 00:12 |
| mithro | cr1901_modern: https://github.com/jimmo/numato-mimasv2-pic-firmware/tree/xmodem | 00:19 |
| tpb | Title: GitHub - jimmo/numato-mimasv2-pic-firmware at xmodem (at github.com) | 00:19 |
| cr1901_modern | mithro: Okay, _most_ of my confusion has been alleviated | 00:30 |
| cr1901_modern | mithro: My Opsis came w/ firmware from Jan 2016. The FX2 appears to have defaulted to serial mode back then | 00:31 |
| cr1901_modern | mithro: (Well "serial and webcam" simultaneously) | 00:31 |
| cr1901_modern | mithro: Does this cound accurate? | 00:32 |
| cr1901_modern | mithro: Is it possible to use --flash-image option of hdmi2usb-mode-switch without sudo? | 01:04 |
| cr1901_modern | Ever since I flashed the new firmware successfully (and confirmed the new firmware is running) I can't access the FPGA from JTAG pins... | 01:05 |
| cr1901_modern | s/firmware/gateware+bios+firmware+mode-switch-working/ | 01:05 |
| mithro | cr1901_modern: install the udev rules | 02:08 |
| mithro | cr1901_modern: that should make it possible to use mode-switch without root | 02:09 |
| cr1901_modern | mithro: I did that, with no effect on --flash-image option | 02:10 |
| cr1901_modern | in any case, I am recompiling openocd right now (b/c they convenient don't enable libftdi usb blaster by default) | 02:10 |
| mithro | Hrm, did you did you connect / disconnect after Opsis after installing the udev rules? | 02:10 |
| cr1901_modern | mithro: No | 02:11 |
| cr1901_modern | Should I have? | 02:11 |
| mithro | Yes | 02:11 |
| mithro | cr1901_modern: how we build openocd at the moment - https://github.com/timvideos/conda-hdmi2usb-packages/blob/master/openocd/build.sh | 02:12 |
| tpb | Title: conda-hdmi2usb-packages/build.sh at master · timvideos/conda-hdmi2usb-packages · GitHub (at github.com) | 02:12 |
| mithro | cr1901_modern: a long while back I started trying to get all our tools to build under windows - https://github.com/timvideos/conda-hdmi2usb-packages/tree/windows | 02:13 |
| tpb | Title: GitHub - timvideos/conda-hdmi2usb-packages at windows (at github.com) | 02:13 |
| mithro | https://github.com/timvideos/conda-hdmi2usb-packages/blob/windows/.appveyor.yml | 02:14 |
| tpb | Title: conda-hdmi2usb-packages/.appveyor.yml at windows · timvideos/conda-hdmi2usb-packages · GitHub (at github.com) | 02:14 |
| mithro | I don't remember where I got too... | 02:14 |
| mithro | https://ci.appveyor.com/project/mithro/conda-hdmi2usb-packages | 02:15 |
| tpb | Title: AppVeyor (at ci.appveyor.com) | 02:15 |
| cr1901_modern | mithro: That's good! Unfortunately, long story short, as-is mode-switch isn't going to really work as intended on Windows due to libusb limitations on Windows. | 02:22 |
| cr1901_modern | mithro: I got sudo problem fixed, and openocd actually talked to the board, but mode-switch hung w/ no output after a while | 02:26 |
| cr1901_modern | would be nice to have an indicator (such as redirecting openocd's stdout to the console) so I could know whether it crashed or not | 02:27 |
| cr1901_modern | https://github.com/timvideos/HDMI2USB-mode-switch/issues/33 Ummm, mithro, what do you mean by "confused"? | 02:32 |
| tpb | Title: Check for common issues when flashing · Issue #33 · timvideos/HDMI2USB-mode-switch · GitHub (at github.com) | 02:32 |
| cr1901_modern | nevermind it works... just takes... a while to load firmware | 02:38 |
| mithro | cr1901_modern: give it --verbose | 03:08 |
| cr1901_modern | mithro: Okay, openocd is in fact working properly. The blaster JTAG port is just slower than my other standalone JTAG programmer | 03:17 |
| cr1901_modern | (can do the write in about 45s vs 140s for blaster) | 03:18 |
| cr1901_modern | But that's a nitpick at this point. Point-blank, opsis is working. I'll worry about my other concerns tomorrow b/c I feel sleep rearing its head... | 03:18 |
| *** rohitksingh has joined #timvideos | 03:29 | |
| *** CarlFK has joined #timvideos | 03:31 | |
| *** ChanServ sets mode: +v CarlFK | 03:31 | |
| mithro | cr1901_modern: yeah, at some point I need to go back and optimise that code | 03:37 |
| *** vystrela has joined #timvideos | 04:09 | |
| vystrela | wondered why this channel suddenly went quiet - turns out I got klined :( | 04:10 |
| *** vystrela is now known as vys | 04:10 | |
| *** Kamilion has quit IRC | 05:06 | |
| *** paradisaeidae_ has joined #timvideos | 05:19 | |
| *** Kamilion has joined #timvideos | 05:20 | |
| *** paradisaeidae_ has quit IRC | 06:02 | |
| *** sb0 has quit IRC | 06:05 | |
| *** paradisaeidae_ has joined #timvideos | 06:24 | |
| *** nueces has quit IRC | 06:39 | |
| *** paradisaeidae_ has quit IRC | 07:16 | |
| paddatrapper | mithro: should be around tomorrow, yes | 07:24 |
| *** sb0 has joined #timvideos | 07:37 | |
| *** rohitksingh1 has joined #timvideos | 08:35 | |
| *** rohitksingh has quit IRC | 08:35 | |
| *** rohitksingh1 has quit IRC | 09:14 | |
| *** rohitksingh has joined #timvideos | 09:18 | |
| *** sb0 has quit IRC | 11:33 | |
| *** sb0 has joined #timvideos | 12:51 | |
| *** CarlFK has left #timvideos | 13:57 | |
| mithro | rohitksingh: afternoon :-P | 14:09 |
| rohitksingh | mithro: good evening! :) | 14:17 |
| mithro | rohitksingh: Hows your USB project going? | 14:36 |
| mithro | Finally! - https://usercontent.irccloud-cdn.com/file/jOwyvGTQ/image.png | 15:33 |
| rohitksingh | mithro: That holy level of awesomeness! :) :o | 15:52 |
| rohitksingh | mithro: Great achievement! | 15:52 |
| mithro | rohitksingh: Needs a whole bunch of cleanup | 15:53 |
| rohitksingh | mithro: still, its excellent achievement! :0 \o/ | 15:55 |
| rohitksingh | mithro: btw all my side projects are on hold for now, atleast until mid-october :( Fully occupied into personal errands | 16:05 |
| cr1901_modern | mithro: Nice work. Someone wants me to add SUMP2 support (when I have time) | 17:51 |
| *** cr1901_modern has quit IRC | 18:29 | |
| *** cr1901_modern has joined #timvideos | 18:32 | |
| *** nueces has joined #timvideos | 20:50 | |
| *** nueces has quit IRC | 21:22 | |
| *** rohitksingh has quit IRC | 23:15 | |
Generated by irclog2html.py 2.13.1 by Marius Gedminas - find it at mg.pov.lt!
