| *** tpb has joined #timvideos | 00:00 | |
| *** CarlFK has joined #timvideos | 00:14 | |
| *** ChanServ sets mode: +v CarlFK | 00:14 | |
| CARAM_ | mithro: you mentioned a repeater flumotion config that you haven't used yet, do you have a template flumo config for that? | 00:17 |
|---|---|---|
| *** FeltonChris has joined #timvideos | 00:24 | |
| *** mparuszewski has quit IRC | 00:31 | |
| *** FeltonChris has left #timvideos | 02:53 | |
| *** loadstar91 has quit IRC | 03:58 | |
| *** loadstar81 has joined #timvideos | 04:04 | |
| *** CarlFK has quit IRC | 04:34 | |
| *** CarlFK has joined #timvideos | 06:29 | |
| *** ChanServ sets mode: +v CarlFK | 06:29 | |
| *** slomo has joined #timvideos | 07:31 | |
| *** rohitksingh has joined #timvideos | 08:13 | |
| *** tija has joined #timvideos | 09:08 | |
| tija | shenki: How can I force USB module to output raw data | 10:54 |
| ayush3504 | tija: hi. did you try the commands list in the developer documentation? it's done by sending 'u' and 'r' I guess | 11:00 |
| tija | ayush3584: How do I send the commands? | 11:01 |
| ayush3504 | tija: connect to the virtual port using a serial terminal, i use a gui based CuteCom | 11:02 |
| ayush3504 | tija: virtual serial port* | 11:03 |
| tija | okay thanks | 11:03 |
| ayush3504 | tija: there are plenty of ways, you can do it in the regular terminal. do a google search ;) | 11:05 |
| ayush3504 | tija: and btw, you send these characters (bytes) together, don't send one at a time. | 11:06 |
| *** rohitksingh1 has joined #timvideos | 12:48 | |
| *** rohitksingh has quit IRC | 12:48 | |
| *** rohitksingh1 is now known as rohitksingh | 12:48 | |
| rohitksingh | mithro: ping | 13:23 |
| mithro | rohitksingh: pong | 13:23 |
| rohitksingh | mithro: did u see my last snippet? what could be the issue with the flickerings? | 13:24 |
| mithro | rohitksingh: there could be a lot of reasons | 13:24 |
| mithro | rohitksingh: I think your best bet to to start looking at the pixel level | 13:24 |
| rohitksingh | I think so too.... | 13:25 |
| mithro | and slow down to like 320x240 resolution | 13:25 |
| rohitksingh | just checked. AD9984A supports 640x480 lowest | 13:27 |
| rohitksingh | actually not support per se...they have given recommended settings for 640x480 as the lowest setting | 13:28 |
| mithro | rohitksingh: rohitksingh then generate some very defined bit patterns | 13:35 |
| mithro | for each pixel | 13:35 |
| mithro | IE 10000001 and 10101010 | 13:35 |
| rohitksingh | yeah, i can try that | 13:36 |
| mithro | rohitksingh: btw how are you clocking the data in from the AD9984A? | 13:36 |
| rohitksingh | at the rising_edge of DATACK. Datasheets tells this "" The output data clock signal is created so that its | 13:37 |
| rohitksingh | rising edge always occurs between data transitions and can be used to latch the output data externally."" | 13:37 |
| mithro | rohitksingh: you might want to try oversampling your data and see if the values are stable | 13:48 |
| rohitksingh | yeah | 13:49 |
| rohitksingh | Also, i have some more tests in mind to detect the problem | 13:49 |
| *** slomo has quit IRC | 14:03 | |
| *** mparuszewski has joined #timvideos | 14:08 | |
| ayush3504 | mithro: you need to tell me what connectors you need on the IR daughter board, review the mechanical spec spreadsheet, discuss the values of "l", "g", "p" in footprint placement drawings linked to the mech spec spreadsheet - http://goo.gl/yyVDO3 | 14:09 |
| tpb | Title: Mechanical specifications for serial expansion board and daughterbaords - Google Tabellen (at goo.gl) | 14:09 |
| *** FeltonChris_ has joined #timvideos | 15:03 | |
| *** mparuszewski has quit IRC | 16:11 | |
| *** mparuszewski has joined #timvideos | 18:12 | |
| *** rohitksingh1 has joined #timvideos | 18:48 | |
| *** rohitksingh is now known as Guest63435 | 18:48 | |
| *** rohitksingh1 is now known as rohitksingh | 18:48 | |
| *** slomo has joined #timvideos | 20:11 | |
| *** FeltonChris_ has left #timvideos | 21:03 | |
| *** slomo has quit IRC | 21:51 | |
| *** tija has quit IRC | 22:41 | |
| *** rohitksingh has quit IRC | 23:37 | |
Generated by irclog2html.py 2.12.1 by Marius Gedminas - find it at mg.pov.lt!