Friday, 2014-06-20

*** tpb has joined #timvideos00:00
*** CarlFK has joined #timvideos00:14
*** ChanServ sets mode: +v CarlFK00:14
CARAM_mithro: you mentioned a repeater flumotion config that you haven't used yet, do you have a template flumo config for that?00:17
*** FeltonChris has joined #timvideos00:24
*** mparuszewski has quit IRC00:31
*** FeltonChris has left #timvideos02:53
*** loadstar91 has quit IRC03:58
*** loadstar81 has joined #timvideos04:04
*** CarlFK has quit IRC04:34
*** CarlFK has joined #timvideos06:29
*** ChanServ sets mode: +v CarlFK06:29
*** slomo has joined #timvideos07:31
*** rohitksingh has joined #timvideos08:13
*** tija has joined #timvideos09:08
tijashenki: How can I force USB module to output raw data10:54
ayush3504tija: hi. did you try the commands list in the developer documentation? it's done by sending 'u' and 'r' I guess11:00
tijaayush3584: How do I send the commands?11:01
ayush3504tija: connect to the virtual port using a serial terminal, i use a gui based CuteCom11:02
ayush3504tija: virtual serial port*11:03
tijaokay thanks11:03
ayush3504tija: there are plenty of ways, you can do it in the regular terminal. do a google search ;)11:05
ayush3504tija: and btw, you send these characters (bytes) together, don't send one at a time.11:06
*** rohitksingh1 has joined #timvideos12:48
*** rohitksingh has quit IRC12:48
*** rohitksingh1 is now known as rohitksingh12:48
rohitksinghmithro: ping13:23
mithrorohitksingh: pong13:23
rohitksinghmithro: did u see my last snippet? what could be the issue with the flickerings?13:24
mithrorohitksingh: there could be a lot of reasons13:24
mithrorohitksingh: I think your best bet to to start looking at the pixel level13:24
rohitksinghI think so too....13:25
mithroand slow down to like 320x240 resolution13:25
rohitksinghjust checked. AD9984A supports 640x480 lowest13:27
rohitksinghactually not support per se...they have given recommended settings for 640x480 as the lowest setting13:28
mithrorohitksingh: rohitksingh then generate some very defined bit patterns13:35
mithrofor each pixel13:35
mithroIE 10000001 and 1010101013:35
rohitksinghyeah, i can try that13:36
mithrorohitksingh: btw how are you clocking the data in from the AD9984A?13:36
rohitksinghat the rising_edge of DATACK. Datasheets tells this "" The output data clock signal is created so that its13:37
rohitksinghrising edge always occurs between data transitions and can be used to latch the output data externally.""13:37
mithrorohitksingh: you might want to try oversampling your data and see if the values are stable13:48
rohitksinghAlso, i have some more tests in mind to detect the problem13:49
*** slomo has quit IRC14:03
*** mparuszewski has joined #timvideos14:08
ayush3504mithro: you need to tell me what connectors you need on the IR daughter board, review the mechanical spec spreadsheet, discuss the values of "l", "g", "p" in footprint placement drawings linked to the mech spec spreadsheet -
tpbTitle: Mechanical specifications for serial expansion board and daughterbaords - Google Tabellen (at
*** FeltonChris_ has joined #timvideos15:03
*** mparuszewski has quit IRC16:11
*** mparuszewski has joined #timvideos18:12
*** rohitksingh1 has joined #timvideos18:48
*** rohitksingh is now known as Guest6343518:48
*** rohitksingh1 is now known as rohitksingh18:48
*** slomo has joined #timvideos20:11
*** FeltonChris_ has left #timvideos21:03
*** slomo has quit IRC21:51
*** tija has quit IRC22:41
*** rohitksingh has quit IRC23:37

Generated by 2.12.1 by Marius Gedminas - find it at!