| *** tpb <[email protected]> has joined #litex | 00:00 | |
| *** TMM <[email protected]> has quit IRC (Quit: https://quassel-irc.org - Chat comfortably. Anywhere.) | 00:34 | |
| *** TMM <[email protected]> has joined #litex | 00:34 | |
| *** Emantor <[email protected]> has quit IRC (Quit: ZNC - http://znc.in) | 02:20 | |
| *** Emantor <[email protected]> has joined #litex | 02:20 | |
| *** Degi <[email protected]> has quit IRC (Ping timeout: 248 seconds) | 03:14 | |
| *** Degi <[email protected]> has joined #litex | 03:16 | |
| *** CarlFK1 <[email protected]> has quit IRC (Ping timeout: 248 seconds) | 05:32 | |
| *** CarlFK1 <[email protected]> has joined #litex | 05:48 | |
| *** CarlFK1 <[email protected]> has quit IRC (Quit: Leaving.) | 05:53 | |
| *** _whitelogger <[email protected]> has quit IRC (Remote host closed the connection) | 06:36 | |
| *** _whitelogger <[email protected]> has joined #litex | 06:39 | |
| *** TMM <[email protected]> has quit IRC (Quit: https://quassel-irc.org - Chat comfortably. Anywhere.) | 14:16 | |
| *** TMM <[email protected]> has joined #litex | 14:16 | |
| *** d_olex <d_olex!~d_olex@user/d-olex:35658> has quit IRC (Ping timeout: 265 seconds) | 15:04 | |
| *** profi200 <profi200!~profi200@user/meow/profi200> has joined #litex | 15:14 | |
| profi200 | Hi, a little bit of a problem maybe someone knows the solution for. I followed the litex install instruction doing it under the oss-cad-suite environment and it installed successfully however none of the litex related commands work. They all fail with "ModuleNotFoundError: No module named 'litex'". I added my steps here in case they are useful plus a few deprecation warnings i got on install that might be relevant. It's an Arch based Linux distro. | 15:25 |
|---|---|---|
| profi200 | https://gist.github.com/profi200/4af02294b06c3ddb74da081d84b087b1 | 15:25 |
| profi200 | I did the install again this time without "--user" and now it seems to work. ¯\_(ツ)_/¯ | 15:53 |
| *** SjefCoder <SjefCoder!~SjefCoder@2a02-a45a-abbc-0-a168-4e9c-3b5-96d3.fixed6.kpn.net> has joined #litex | 17:31 | |
| SjefCoder | Yo peeps. The spi config allows you to set the mode: Manual operation (CS handled by User, direct recopy of ``sel``), useful for Bulk transfers. I use spimaster_cs_write to set the mode and chip select to low. It works (can see it in the logic analyzer). However, spimaster_mosi_write does nothing! Only when I use spimaster_control_write. But that | 17:34 |
| SjefCoder | goes against the whole purpose of handling CS by user and thus being able to do bulk transfers... | 17:34 |
| SjefCoder | What am I overlooking. Why can't I manually assert CS low and then just do mosi writes ? Why do I have to always use the spi control? | 17:38 |
| *** SjefCoder <SjefCoder!~SjefCoder@2a02-a45a-abbc-0-a168-4e9c-3b5-96d3.fixed6.kpn.net> has quit IRC (Quit: Client closed) | 17:53 | |
| *** d_olex <d_olex!~d_olex@user/d-olex:35658> has joined #litex | 20:11 | |
| *** ElfenKaiser <ElfenKaiser!~deadsalmo@2a0a-a540-e86c-0-2c6c-f7c1-4cfe-476f.ipv6dyn.netcologne.de> has joined #litex | 20:12 | |
| *** SjefCoder <[email protected]> has joined #litex | 20:31 | |
| *** CarlFK1 <[email protected]> has joined #litex | 20:53 | |
| *** SjefCoder <[email protected]> has quit IRC (Quit: Client closed) | 23:38 | |
| *** ElfenKaiser <ElfenKaiser!~deadsalmo@2a0a-a540-e86c-0-2c6c-f7c1-4cfe-476f.ipv6dyn.netcologne.de> has quit IRC (Quit: Konversation terminated!) | 23:54 | |
| *** CarlFK1 <[email protected]> has quit IRC (Ping timeout: 252 seconds) | 23:56 | |
Generated by irclog2html.py 2.17.2 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!